Wheel bucket sand washing machine
Author: Zhengzhou Qingshan Information Technology Co., Ltd. date: October 30, 2019 popularity: 10
Product introduction
xsd series wheel bucket sand washing machine is a kind of high-efficiency sand washing equipment, which is developed by using domestic and foreign technology and combined with the actual situation of sand industry. It is mainly used to remove trace stone powder and impurities from the mixed sand produced by the sand making machine, so as to improve the quality of sand. It has the functions of cleaning, dewatering and grading. It is widely used in washing, grading and removing impurities of fine-grained and coarse-grained materials in metallurgy, building materials, hydropower and other industries, especially suitable for building sand and road building sand.
The new type of steel mesh wheel bucket sand washing machine produced by our company has the characteristics of high cleaning degree, reasonable structure, large processing capacity, small power consumption and less sand loss in the process of sand washing. Especially, its transmission parts are isolated from water and sand, so the failure rate is much lower than other similar sand washing machines at present. It is a better choice for upgrading and upgrading domestic sand washing industry.
working principle
??? When the sand washing machine works, the motor drives the impeller to rotate slowly after decelerating through the triangle belt, reducer and gear. The sand and gravel enter the washing tank from the feeding groove, and then roll and grind each other under the drive of the impeller, so as to remove the impurities on the surface of the sand and stone, and damage the water vapor layer covering the sand particles, so as to facilitate dehydration; then add water at the same time to form a strong water flow, and timely remove impurities and impurities The foreign matters with small specific gravity are taken away and discharged from the overflow outlet washing tank to complete the cleaning function. The clean sand is taken away by the blade, and finally the sand is poured into the discharge tank from the rotating impeller to complete the whole sand cleaning process.
Highlight advantages
High cleaning rate and low failure rate
The speed of motor and reducer is slow, the effect is good and the fault is few.
The structure is novel and the maintenance is simple
The new generation of sand washing machine adopts punching steel mesh, which is more durable.
Large processing capacity and low power consumption
Customized, the output of a single equipment is 200 tons, more energy-saving.
Less loss of fine sand, good cleaning and dewatering effect
Equipped with dewatering screen, fine sand recovery machine, high sand quality, less loss of fine sand.
technical parameter
model
|
Impeller specification (outer diameter × width) (mm)
|
Impeller speed (r/min)
|
Feed size (mm)
|
Treatment capacity (t/h)
|
Motor power (kw)
|
Reducer model
|
Dimensions (length × width × height) (mm)
|
XSD2610
|
Φ2600×1000
|
one point one seven eight
|
≤10
|
20-50
|
five point five
|
ZQ50-50-I-Z
|
3255×1982×2690
|
XSD2816
|
Φ2800×1600
|
one point one seven seven
|
≤10
|
30-60
|
7.5-11
|
ZQ65-50-I-Z
|
3540×3000×2880
|
XSD3016
|
Φ3000×1600
|
one point one seven nine
|
≤10
|
50-120
|
11-15
|
ZQ65-50-I-Z
|
3845×3000×3080
|
XSD3018
|
Φ3000×1800
|
one point eight three two
|
≤10
|
80-150
|
11-15
|
ZQ65-50-I-Z
|
3615×3032×3130
|
Note: the above technical parameters are subject to change without prior notice, subject to the current new technical parameters of our company, and can be customized according to the user's requirements.
Engineering cases
-
120-150 ton stone powder sand washing production line
major equipment : silo, two 1000 belt conveyors, two 3018 bucket sand washing machines, one 500 fine sand reclaimer, etc;
Cleaning materials : stone powder for stone production in mines
Particle size of raw materials : below 5mm
yield :120-150t/h
-
On site shooting of machine-made sand washing production line
major equipment : sand conveyor, belt conveyor, belt conveyor, sand feeder, etc;
Processing materials : weathered sandstone, below 180mm
Particle size of finished product Below: 5mm
yield :120-150t/h
Related product recommendation
Learn more Please leave your contact information and we will contact you within 24 hours: Tel: 13721431212 (micro signal) 0371-56630331